Lowrance x4 pro manual download
Looking for:
Lowrance x4 pro manual download - |
LOWRANCE X-4 PRO INSTALLATION AND OPERATION INSTRUCTIONS MANUAL Pdf Download | ManualsLib
Manual Lowrance X-4 Pro Fishfinder
Table Of Contents. Quick Links. X-4 Pro. Table of Contents. Previous Page. Next Page. Lowrance x fish radar: operation instruction 38 pages. Page 2 Navico. Any unauthorized commercial distribution of this manual is strictly prohibited. Lowrance is a registered trademark of Navico.
Transom Mounting Di- agonal viewing area: 4" Extended storage in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty. Page 7: Recommended Tools And Supplies Depending on your sonar unit's connectors, your transducer cable may also have the sonar unit's power cable attached to it.
If that is the case, be sure to install the transducer first, before connecting the power cable to a power source. See the instructions later in this manual for connect- ing the power cable to a battery or other power supply.
Page 8 NOTE: Some aluminum boats with strakes or ribs on the outside of the hull create large amounts of turbulence at high speed. These boats typically have large outboard motors capable of propelling the boat at speeds faster than 35 mph.
Typically, a good transom location on aluminum boats is between the ribs closest to the engine. For most situations, you should install your Skimmer transducer so that its centerline is level with the bottom of the boat hull.
This will usually give you the best combination of smooth water flow and protec- tion from bangs and bumps. Page Transom Transducer Assembly And Mounting varies from hull to hull, even from different installations on the same hull. This is caused by differences in hull lay-up and construction. Second, the transducer angle cannot be adjusted for the best fish arches.
This can be a problem on hulls that sit with the bow high when at rest or at slow trolling speeds. Page 11 Reassemble the transducer and bracket and place them against the transom.
Again, check to see if you can move the transducer so it's pa- rallel with the ground. If you can, then go to step 3. If it doesn't, repeat step 2, but use a different alignment letter. Page 12 Transom Transom Position transducer mount on transom and mark mounting holes. Side view shown at left and seen from above at right. Attaching transducer to transom.
Remove the transducer from the bracket and re-assemble it with the cable passing through the bracket over the bolt as shown in the following figures. Page 13 Bottom hull Deep-"vee" hull Flat-bottom hull Align transducer centerline with hull bottom and attach to transom. Route the transducer cable through or over the transom to the sonar unit. Make sure you leave some slack in the cable at the transducer.
Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer. Page Transducer Orientation And Fish Arches Transducer Orientation and Fish Arches If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds. Partial fish arches Transducer aimed Transducer aimed Page 16 ers.
The sonar signal must pass through solid fiberglass. A successful transducer installation can be made on hulls with flotation materials such as plywood, balsa wood or foam between layers of fiberglass if the material is removed from the chosen area.
See the figure below. Page Testing Determines Best Location Testing Determines Best Location Ideally, the shoot-thru transducer should be installed as close to the transom as possible, close to the centerline. This will give you the best performance during high speed maneuvers. Anchor the boat in about 30 feet of water. Add a little water to the sump of the boat. Page Shoot-Thru-Hull Installation hull. This is especially true if you have to turn sensitivity all the way up to get a decent bottom signal.
Most people can get good results by following steps 1 through 3, so this step is optional. If you want to make an extra effort to be absolutely sure that your selected location will work under all conditions, make a test run with the boat on plane and observe the bottom signal. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the package and place them on the paper plate. Thoroughly stir the two compounds together until the mixture has a uniform color and consistency.
Do not mix too fast or bubbles will form in the epoxy. The FM-6 kit includes an instruction sheet, part , which contains a template for cutting out the mounting hole. This document can be downloaded free from www. Page Bracket Installation [2. Drill a 1" The best location for this hole is immediately under the gimbal bracket location. Slots in the base allow routing the cable from beneath the mount.
Then, hold the sonar unit vertically and slide it onto the bracket from above. It uses the optional PPP portable power pack. The power pack and portable transducers expand the uses for your sonar.
The PPP- 12 has a quick-release mounting bracket built into the case. Installing the Batteries Open the case and lay it flat. The latch is located below the handle. Insert eight "AA" size batteries into the battery adapter and place it in the battery compartment.
Page Portable Transducer Assembly Ratchet To mount the sonar, slide the unit onto the bracket from above left. To adjust the view, press and release spring-loaded ratchets while tilt- ing the unit right. To adjust the viewing angle, pinch the quick-release mount's ratchets with one hand, then tilt the unit with your other hand. Release the rat- chets and the unit locks into the new position. Page 26 Make sure there is one washer on each side of the transducer, inside the bracket.
Slide the other washer over the end of the bolt and screw on the nut. Screw the suction cup onto the bracket using the supplied screw and flat washer. Portable Transducer Storage There is room inside the power pack for the portable transducer.
When you're finished fishing, tilt the sonar down to the storage position. Open the case and lay it flat. Unplug the power connector from the battery compartment socket.
You will use these keys to adjust most features and functions on the X-4 Pro. To switch menus, press repeatedly. Press to clear menus MENU from the screen. The Backlight menu with backlight turned on. Display The lights will flash for about 10 seconds when the unit is turned on. The backlight menu will appear on the screen. The bottom signal scrolls across the screen from right to left. The line at the top of the screen represents the surface.
The bottom depth — Page Zoom Depth Range menu with Manual setting selected left. Range Size menu with ft highlighted right. Zoom The zoom feature enlarges all images on the screen by doubling the size of the echoes a 2X zoom. For example, if the current auto depth range is 0 to 60 feet, Zoom will show an enlarged view of the water column from 30 feet to 60 feet, always keeping the bottom in view. The top of the depth range scale returns to zero.
NOTE: Using the Zoom command while in auto Zoom mode will always en- large the echoes near the bottom, because auto Range always keeps the bottom displayed in the lower portion of the screen. Page 33 Sensitivity set to manual mode left. Sensitivity scroll bar right. You can change the sensitivity level whether you are in Auto Sensitivity mode or Manual Sensitivity mode. The adjustment method works the same in both modes, but gives you slightly different results.
Comments
Post a Comment